Matronics Email Lists Forum Index Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
 
 Get Email Distribution Too!Get Email Distribution Too!    FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Thanks for the list Matt! - Plans Rev. pg 11-03

 
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV14-List
View previous topic :: View next topic  
Author Message
Tim Olson



Joined: 25 Jan 2007
Posts: 2872

PostPosted: Mon Jan 07, 2013 6:26 am    Post subject: Thanks for the list Matt! - Plans Rev. pg 11-03 Reply with quote

Thanks to Matt for setting up an RV-14 email list. Those of you
on this list (maybe very few at this point) who know me, know
that I prefer email based lists...the messages pop into
your inbox where you can address them quickly. It makes for
a speedy way to pass along info.

I'm builder 140032, and got my kit 12/21/2012. So far I'm done
with section 11 and 1/2 way through 12 almost. I find that the
RV-14 plans in some cases so far, are perhaps a little more
vague than the RV-10, although the kit itself has some nice
little improvements. In the section on countersinking the spar
in section 11, they do show the max depth and width of the
countersinks you create, but, they don't go into detail as to
what the ultimate goal of the countersunk hole will be. In the
-10 plans they have you test dimple a scrap of aluminum so that
you get the depth to a workable depth for assembly later.
Anyway, it does take a little interpreting and reading ahead
if you're a 1st time builder. I have a website regarding
my RV-10 at http://www.MyRV10.com, and although I still update
it, it won't be changing drastically in the future. I also
have one set up for the RV-14 at http://www.MyRV14.com that
I will use to document the build, but I will not be spending
nearly the time writing as I did on the other plane. I probably
have as much time into writing as building on that kit.

I did have one plans correction I found, and Van's has already
changed it on their plans, but it somehow didn't make it into
my plans when they shipped just a few weeks ago. On page 11-03
the "AFT / UP / Inboard" label was wrong in 2 diagrams, but
they have it changed now to "FWD / UP / Inboard", so they were
already on it. I'm sure we'll find more changes as we go
through the build.

I just wanted to make a quick introduction and let anyone
else who signed on the list know that I'll be monitoring
the list, so email here when you run into questions or issues.

Tim
RV-10 N104CD


- The Matronics RV14-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV14-List
Back to top
View user's profile Send private message Send e-mail
dave.saylor.aircrafters(a
Guest





PostPosted: Mon Jan 07, 2013 7:00 am    Post subject: Thanks for the list Matt! - Plans Rev. pg 11-03 Reply with quote

Hi Tim, can't wait to see your progress.

Anyone else wish there was a 540 option?

Dave Saylor
831-750-0284 CL


On Mon, Jan 7, 2013 at 6:26 AM, Tim Olson <Tim(at)myrv10.com (Tim(at)myrv10.com)> wrote:
[quote] --> RV14-List message posted by: Tim Olson <Tim(at)myrv10.com (Tim(at)myrv10.com)>

Thanks to Matt for setting up an RV-14 email list. Those of you
on this list (maybe very few at this point) who know me, know
that I prefer email based lists...the messages pop into
your inbox where you can address them quickly.  It makes for
a speedy way to pass along info.

I'm builder 140032, and got my kit 12/21/2012.  So far I'm done
with section 11 and 1/2 way through 12 almost.  I find that the
RV-14 plans in some cases so far, are perhaps a little more
vague than the RV-10, although the kit itself has some nice
little improvements.  In the section on countersinking the spar
in section 11, they do show the max depth and width of the
countersinks you create, but, they don't go into detail as to
what the ultimate goal of the countersunk hole will be.  In the
-10 plans they have you test dimple a scrap of aluminum so that
you get the depth to a workable depth for assembly later.
Anyway, it does take a little interpreting and reading ahead
if you're a 1st time builder.  I have a website regarding
my RV-10 at http://www.MyRV10.com, and although I still update
it, it won't be changing drastically in the future.  I also
have one set up for the RV-14 at http://www.MyRV14.com that
I will use to document the build, but I will not be spending
nearly the time writing as I did on the other plane.  I probably
have as much time into writing as building on that kit.

I did have one plans correction I found, and Van's has already
changed it on their plans, but it somehow didn't make it into
my plans when they shipped just a few weeks ago.  On page 11-03
the "AFT / UP / Inboard" label was wrong in 2 diagrams, but
they have it changed now to "FWD / UP / Inboard", so they were
already on it.  I'm sure we'll find more changes as we go
through the build.

I just wanted to make a quick introduction and let anyone
else who signed on the list know that I'll be monitoring
the list, so email here when you run into questions or issues.

Tim
RV-10 N104CD

====================================
" target="_blank">http://www.matronics.com/Navigator?RV14-List
====================================
MS -
k">http://forums.matronics.com
====================================
e -
         -Matt Dralle, List Admin.
t="_blank">http://www.matronics.com/contribution
====================================



[b]


- The Matronics RV14-List Email Forum -
 

Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:

http://www.matronics.com/Navigator?RV14-List
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Matronics Email Lists Forum Index -> RV14-List All times are GMT - 8 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum


Powered by phpBB © 2001, 2005 phpBB Group