 |
Matronics Email Lists
Web Forum Interface to the Matronics Email Lists
|
| View previous topic :: View next topic |
| Author |
Message |
pdelano(at)telus.net
Guest
|
 Posted: Mon Oct 27, 2014 3:43 pm Post subject: 7-V-7-4 Inboard Trailing Edge |
 |
|
Hi All,
I am puzzled. As far as I can determine for the right wing (which is hung on the wall) I cut out the inboard trailing edge as shown on the 10/2002 drawings, specifically made the the fore to aft cut 22 mm deep to allow for clearance of 7V4-4 as shown on the lower left corner of 7-V-7. However on the left wing the trailing edge at 7V4-4 does not seem to want to come flush with the trailing edge of the top rear skin. It seems I would need to make this cut about 27 mm deep. Was there an update to the drawings for this dimension that I just don’t seem to be able to find now. I am trying not to jump to a solution that is not required.
Thank you in advance for any help with this query.
Regards,
Perry
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
 |
JohnDRead(at)aol.com
Guest
|
| Posted: Tue Oct 28, 2014 3:47 pm Post subject: 7-V-7-4 Inboard Trailing Edge |
|
|
Call the factory.
John Read
Home: 303.648.3261
Mobile: 719.494.4567
In a message dated 10/27/2014 5:43:48 P.M. Mountain Daylight Time, pdelano(at)telus.net writes:
| Quote: |
Hi All,
I am puzzled. As far as I can determine for the right wing (which is hung on the wall) I cut out the inboard trailing edge as shown on the 10/2002 drawings, specifically made the the fore to aft cut 22 mm deep to allow for clearance of 7V4-4 as shown on the lower left corner of 7-V-7. However on the left wing the trailing edge at 7V4-4 does not seem to want to come flush with the trailing edge of the top rear skin. It seems I would need to make this cut about 27 mm deep. Was there an update to the drawings for this dimension that I just don’t seem to be able to find now. I am trying not to jump to a solution that is not required.
Thank you in advance for any help with this query.
Regards,
Perry
| Quote: |
====================================
List href="http://www.matronics.com/Navigator?Zenith701801-List">http://www.matronics.com/Navigator?Zenith701801-List
====================================
ms.matronics.com/">http://forums.matronics.com
====================================
tp://www.matronics.com/contribution">http://www.matronics.com/contribution
====================================
|
|
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
pdelano(at)telus.net
Guest
|
| Posted: Wed Oct 29, 2014 6:08 am Post subject: 7-V-7-4 Inboard Trailing Edge |
|
|
Hi John,
As always; good advice.
Regards,
Perry
From: owner-zenith701801-list-server(at)matronics.com [mailto:owner-zenith701801-list-server(at)matronics.com] On Behalf Of JohnDRead(at)aol.com
Sent: Tuesday, October 28, 2014 4:47 PM
To: zenith701801-list(at)matronics.com
Subject: Re: 7-V-7-4 Inboard Trailing Edge
Call the factory.
John Read
Home: 303.648.3261
Mobile: 719.494.4567
In a message dated 10/27/2014 5:43:48 P.M. Mountain Daylight Time, pdelano(at)telus.net (pdelano(at)telus.net) writes:
| Quote: |
Hi All,
I am puzzled. As far as I can determine for the right wing (which is hung on the wall) I cut out the inboard trailing edge as shown on the 10/2002 drawings, specifically made the the fore to aft cut 22 mm deep to allow for clearance of 7V4-4 as shown on the lower left corner of 7-V-7. However on the left wing the trailing edge at 7V4-4 does not seem to want to come flush with the trailing edge of the top rear skin. It seems I would need to make this cut about 27 mm deep. Was there an update to the drawings for this dimension that I just don’t seem to be able to find now. I am trying not to jump to a solution that is not required.
Thank you in advance for any help with this query.
Regards,
Perry
|
0123456789 | Quote: | | ==================================== |
0 | Quote: | | ==================================== |
1 | Quote: | | ==================================== |
2 | Quote: | | ==================================== |
3 | Quote: | | ==================================== |
4 | Quote: | | ==================================== |
5 | Quote: | | ==================================== |
6 | Quote: | | ==================================== |
7
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4765 / 10/28/14
[quote][b]
| | - The Matronics Zenith701801-List Email Forum - | | | Use the List Feature Navigator to browse the many List utilities available such as the Email Subscriptions page, Archive Search & Download, 7-Day Browse, Chat, FAQ, Photoshare, and much more:
http://www.matronics.com/Navigator?Zenith701801-List |
|
|
|
| Back to top |
|
|
|
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum
|
Powered by phpBB © 2001, 2005 phpBB Group
|
Get Email Distribution Too!
FAQ
Search
Memberlist
Usergroups
Register
Profile
Log in to check your private messages
Log in
