Matronics Email Lists :: View topic

Matronics Email Lists
Web Forum Interface to the Matronics Email Lists

Get Email Distribution Too! FAQ Search Memberlist Usergroups Register

Profile Log in to check your private messages Log in

horizontal stab

Matronics Email Lists Forum Index -> MurphyMoose-List

View previous topic :: View next topic

Author Message

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Sun Mar 28, 2010 11:15 am Post subject: horizontal stab

Hi Guys 



Getting ready for paint, and trying to figure out if I can install the horizontal stab and elevator after riveting the  fiber glass fairing , it doesn't look like it .  Any suggestions on this?  It will be  hard to paint separately .  If I install the horizontal stab then I cannot get it out of the garage.



Henry

_________________
Currently building a Murphy Moose - any help would be appreciated.

westcoastkitplanes(at)gma
Guest

Posted: Sun Mar 28, 2010 4:10 pm Post subject: horizontal stab

Henry,



Cut the fiberglass fairing so the horizontal stab and vertical stab pieces are separate for installation.  You could rivet the vertical stab fairing in place, but I would use screws to install the horizontal stab fairing pieces in place; you'll have to remove these pieces at a later date for inspection anyways.  Doing it this way will allow you to install elevator and stab.

 

Cheers,

Jeff

On Sun, Mar 28, 2010 at 12:15 PM, HBaker <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)> wrote:

[quote] --> MurphyMoose-List message posted by: "HBaker" <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)>

 

 Hi Guys

 

 Getting ready for paint, and trying to figure out if I can install the horizontal stab and elevator after riveting the  fiber glass fairing , it doesn't look like it .  Any suggestions on this?  It will be  hard to paint separately .

  

 Henry

 

 --------

 Currently building a Murphy Moose - any help would be appreciated.

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=292097#292097

 

 

 

 

 

 

 

 ===========

 List" target="_blank">http://www.matronics.com/Navigator?MurphyMoose-List

 ===========

 http://forums.matronics.com

 ===========

 le, List Admin.

 ="_blank">http://www.matronics.com/contribution

 ===========

 

 

 

 [b]

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Sun Mar 28, 2010 5:41 pm Post subject: Re: horizontal stab

Not real clear on what you are saying, do I put screws in the whole fairing , Or cut the fairing some where???

_________________
Currently building a Murphy Moose - any help would be appreciated.

westcoastkitplanes(at)gma
Guest

Posted: Sun Mar 28, 2010 10:29 pm Post subject: horizontal stab

Henry,



You have to cut the fairings. I'll see if I can get a picture to you tomorrow or within a day or two.



cheers,

Jeff

On Sun, Mar 28, 2010 at 6:41 PM, HBaker <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)> wrote:

 [quote]--> MurphyMoose-List message posted by: "HBaker" <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)>

  

 Not real clear on what you are saying, do I put screws in the whole fairing , Or cut the fairing some where???

 

 --------

 Currently building a Murphy Moose - any help would be appreciated.

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=292154#292154

 

 

 

 

 

 

 

 ===========

 List" target="_blank">http://www.matronics.com/Navigator?MurphyMoose-List

 ===========

 http://forums.matronics.com

 ===========

 le, List Admin.

 ="_blank">http://www.matronics.com/contribution

 ===========

 

 

 

 [b]

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Mon Mar 29, 2010 1:39 am Post subject: Re: horizontal stab

I think we are talking about different fairings , I was talking about the one you get in two pieces  and have to join with fiberglass it attaches to the fuselage and the vertical fin, I did not receive any for the ends of the horizontal  stab .

Henry

_________________
Currently building a Murphy Moose - any help would be appreciated.

westcoastkitplanes(at)gma
Guest

Posted: Mon Mar 29, 2010 8:51 am Post subject: horizontal stab

Henry,

  

 I was referring to the main fairing (V & H Stab), yes you get it in two halves and have to put it together. But for the ease of doing inspections/maintenance put a cut line in the fairing; separating the V stab from the H stab.

   

 I am not referring to the fiberglass tips on the stab, those should be a no brainer.

  

 My offer to provide you with a picture of the main stab fairing installation is still open........ If we're on the same page.

  

 Cheers,

 Jeff

 



 

 On Mon, Mar 29, 2010 at 2:39 AM, HBaker <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)> wrote:

 [quote]--> MurphyMoose-List message posted by: "HBaker" <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)>

 

I think we are talking about different fairings , I was talking about the one you get in two pieces  and have to join with fiberglass it attaches to the fuselage and the vertical fin, I did not receive any for the ends of the horizontal  stab .

 



Henry



--------

Currently building a Murphy Moose - any help would be appreciated.





Read this topic online here:



http://forums.matronics.com/viewtopic.php?p=292177#292177

  as List Un/Subscription,

 www.matronics.com/Navigator?MurphyMoose-List" target="_blank">http://www.matronics.com/Navigator?MurphyMoose-List

 ronics.com/" target="_blank">http://forums.matronics.com

 Matt Dralle, List Admin.

 =====



[b]

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Mon Mar 29, 2010 12:19 pm Post subject: Re: horizontal stab

I'll take you up on the picture ,  if you can get one,  it certainly  would be appreciated ,   and is there fairings for the ends of the horizontal stab  and elevator as well ???

_________________
Currently building a Murphy Moose - any help would be appreciated.

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Tue Apr 06, 2010 4:42 am Post subject: Re: horizontal stab

Jeff I have the one on the leading edge of the horizontal stab.

_________________
Currently building a Murphy Moose - any help would be appreciated.

bill(at)kidzploration.com
Guest

Posted: Tue Apr 06, 2010 8:45 am Post subject: horizontal stab

I found these guys to be very active and very helpfulrebel-builders(at)dcsol.com (rebel-builders(at)dcsol.com)

 You can sign up on the Merphy sight

 its at the bottom of one of the pages, don't remember which one

 but its easy to find 

 cheers Bill

 

On Tue, Apr 6, 2010 at 8:42 AM, HBaker <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)> wrote:

[quote] --> MurphyMoose-List message posted by: "HBaker" <henry.baker(at)nf.sympatico.ca (henry.baker(at)nf.sympatico.ca)>

 

 Jeff I have the one on the leading edge of the horizontal stab.

 

 --------

 Currently building a Murphy Moose - any help would be appreciated.

 

 

 

 

 Read this topic online here:

 

 http://forums.matronics.com/viewtopic.php?p=293167#293167

 

 

 

 

 

 

 

 ===========

 List" target="_blank">http://www.matronics.com/Navigator?MurphyMoose-List

 ===========

 http://forums.matronics.com

 ===========

 le, List Admin.

 ="_blank">http://www.matronics.com/contribution

 ===========

 

 

 

 [b]

HBaker

Joined: 16 Nov 2008
Posts: 119

Posted: Wed Apr 07, 2010 9:26 am Post subject: Re: horizontal stab

Thanks Bill 



I'll try to get hold of them.

_________________
Currently building a Murphy Moose - any help would be appreciated.

Display posts from previous:

	Matronics Email Lists Forum Index -> MurphyMoose-List	All times are GMT - 8 Hours
Page 1 of 1

Jump to:

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You can download files in this forum