Matronics Email Lists

Thanks Jerry! The photo is very helpful. How long of an arm are you using from the ram ball to your iPad?

Sent from my iPad

[quote] On Apr 15, 2023, at 4:20 PM, Jerry Goldberg <jkgcpa@ix.ne ...

I’ve become tired of using my iPad mini 6 on my lap when flying for ForeFlight
Information. Has a one here figured out how to mount an iPad on the panel. If so, could you share that information ...

This was posted by Kyle Lawler, VP of Operations at Allegro LSA. I went online
And confirmed the Obituaries.

It is with great sadness, that I must inform everyone of the passing of Doug and Betty ...

Has anyone here installed an ADS-B compliant system in their Allegro? And
If so, what type was it and would you please share the information with the group?

Thanks,
Larry Edson
N4362C

I replaced the main gear wheel bearing last year. Both the mains and the nose wheel are the same and the bearings are the same. There was no need to dismount the tire or split the rim. I simply rem ...

Hugh,
I assume that your carburetors have been rebuilt recently since your engine has 700+ hours on it. Rotax recommends that the Bing carbs be rebuilt every 200 hours. During my carb rebuild at 2 ...

Dee,
You maybe able to source the fuse holder you need from Doug Hempstead at Allegro USA. That's my source for replacement parts.

The starting procedures are somewhat different for a Rotax eng ...

Dee,
I fly an Allegro 2000 but I would assume that power receptacles are the same. The power receptacle is protected by a fuse that is located on the panel near the receptacle. Check the fuse and ...

I've done this a number of times. All you have to do is remove the three bolts that attach the brake disk to the wheel. Then remove the cotton pin from the axle shaft, remove the wheel retaining nu ...

I still follow the group. There isn't very many posts, but I'm still able to
Glean some information from time to time.

Larry Edson
N4362C

Has anyone looked into an ADS B solution for our Allegro aircraft? Also has there been any word from Allegro USA about a solution and how we should proceed?

Thanks,

Larry Edson
N4362C

Mine was not a problem with turning the lever to unlock it, mine was with
The circumference of the gas cap. I replaced the cap with one from Aircraft Spruce and there was not a problem after that. ...

I spoke with Doug Hempstead at AllegroLSA. He is going to make me a
couple of the required O rings for the gascolator bowl.

Thanks Everyone.

Larry Edson
N4362C

I spoke with Doug Hempstead at AllegroLSA. He is going to make me a
couple of the required O rings for the gascolator bowl.

Thanks Everyone.

Larry Edson
N4362C

Does anyone know the size of the gascolator O ring on the Allegro 2000? Mine has started to leak.

Thanks,

Larry Edson
N4362C

The battery in my 2006 Allegro 2000 is getting weak. Does anyone know
What the recommended battery replacement is?

Thanks,

Larry Edson
N4362C

Hugh,

I would check the noise canceling capacitors. They do fail with exposure to heat and humidity and they are not hard to check.
The following document will help you to understand the vario ...

I've been using auto gas with ethanol since I've owned the airplane and the
PO only used auto gas.
Yes, the gas cap can be adjusted using a small nut inside the cap. But I know that isn't the pr ...

I've noticed that the gas cap on my allegro 2000 is getting very difficult to remove and replace. I Believe the the plastic cap has swelled or expanded to the point that it can't be removed with out ...

I've noticed that the gas cap on my allegro 2000 is getting very difficult to remove and replace. I Believe the the plastic cap has swelled or expanded to the point that it can't be removed with out ...